Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
line-reflect-reflect technique
Post: #1

The Line-Reflect-Reflect (LRR) technique is a new self-calibration procedure for the calibration of vector network analyzers (VNA), which are used for complex scattering parameter measurements of microwave devices.

The calibration circuits of LRR method consist of partly unknown standards, where L symbolizes a line element and R represents a symmetrical reflection standard. The calibration circuits are all of equal mechanical length. This is advantageous because the complexity of test fixture can be reduced. The LRR method is able to perform a calibration on the basis of reflective networks, which leads to an enlargement of the bandwidth.
The calibration structures of the LRR method can be realized very easily as etched structures in microstrip technology or as metal plates for free space applications.

LRR- LINE REFLECT REFLECT is a new self-calibration procedure for the calibration of vector network analyzers (VNA). VNA measure the complex transmission and reflection characteristics of microwave devices. The analyzers have to be calibrated in order to eliminate systematic errors from the measurement results.
The LRR calibration circuits consist of partly unknown standards, where L symbolizes a line element and R represents a symmetrical reflection standard. The calibration circuits are all of equal mechanical length. The obstacle, a symmetrical-reciprocal network is placed at three consecutive positions. The network consists of reflections, which might show a transmission. The calibration structures can be realized very easily as etched structures in microstrip technology.
During the calibration [G], [H], which represents the systematic errors of the VNA is eliminated in order to determine the unknown line and obstacle parameters.

Microwave devices are devices operating with a signal frequency range of 1-300GHz. A microwave circuit ordinarily consists of several microwave devices connected in some way to achieve the desired transmission of a microwave signal.
The various microwave solid state devices are,
* Tunnel diodes
These are also known as Esaki diodes. It is a specially made PN junction device which exhibits negative resistance over part of the forward bias characteristic. Both the P and the N regions are heavily doped. The tunneling effect is a majority carrier effect and is very fast. It is useful for oscillation and amplification purposes. Because of the thin junction and shot transit time, it is useful for microwave applications in fast switching circuits.
* Transferred electron devices
These are all two terminal negative resistance solid state devices which has no PN junction. Gunn diode is one of the transferred electron devices and which works with the principle that there will be periodic fluctuations in the current passing through an n-type GaAs substrate when the applied voltage increases a critical value i.e. 2-4Kv/cm.
*Avalanche transit-time devices
These are used for amplification purposes. And the basic principle is the voltage breakdown at the reverse biased PN junction with the supply of electrons and holes.
These microwave solid state devices are used for generation and amplification of microwave signals by means of velocity-modulation theory. The interconnection of two or more microwave devices is regarded as a microwave junction. From the network theory a two-port device can be described by a number of parameter sets, such as the H, Y, Z and ABCD. All these network parameters relate total voltages and total currents at each of the two ports. If the frequencies are in the microwave range, the two port network representation is as shown in FIG: 1.
The logical variables are traveling waves rather than total voltages and total currents. These are S-parameters, which are expressed as
b1= S11a1+S12a2
b2= S21a1+S22a2

A typical microwave system usually consists of a transmitter subsystem, including a microwave oscillator, waveguides, and a transmitting antenna, and a receiver subsystem that includes a receiving antenna, transmission line or waveguide, a microwave amplifier, a receiver.

It measures the complex transmission and reflection characteristics of microwave devices. This is achieved by comparing the signal input to the device, with the signal either transmitted through or reflected back from the device. They incorporate very narrow bandwidth receivers tuned to the signal source frequency and give a direct readout of the four coefficients contained in a scattering matrix-the scattering or Ëœsâ„¢ parameters, each of which has magnitude and phase elements. The network analyzer was controlled by an external personal computer. The raw measurement data have been read out and processed on a computer.

Incident signal
Microwave source
Test set
Microwave Device
REF signal
Transmitted signal
Reflected signal
Display system
External PC

The calibration circuits of the LRR method consists of,
Line elements of mechanical length, l and
A symmetrical, reciprocal network i.e. an obstacle network placed at three consecutive positions.
Two LRR procedures are,
LRR method without transmission
LRR method with a weak transmission

The calibration circuits can be described with the help of the line parameter k, a reflection coefficient , and wave parameters(s- parameters) a1,i, ¦¦.a4,i and b1,i,¦¦.b4,i, i=1,2,3 , which are set according to the setup shown below.
Within the self calibration procedure the reflection coefficient , and the line parameter k are determined. Suppose, the error two-port [G]-1 is described by the following equation with,

Considering the first structure the equation can be rewritten as follows,

So that another bilinear relation results

The reflection coefficients of the different structures can be related to the measurement values Vl,i and Vr,i with
l,I = K4 Vl,1
l,2 = K2 Vl,2
l,3 = Vl,3
r,1 = K4 -1 Vr,1
r,2 = K2 -1 Vr,2
r,3 = -1 Vr,3
On the basis of the measurement of four reflection coefficients the unknown error two port parameters can be eliminated. This can be performed with the help of the cross ratio,
((y1-y2)*(y3-y4)) / ((y1-y4)*(y3-y2)) =
((x1-x2)*(x3-x4) / (( x1-x4)*(x3-x2)
which generally holds for a bilinear transformation also known as Mobius transformation of two variables xi and yi, with i=1,¦.4 and the constants C1¦C4.
Xi = (C1*yi +C2) / (C3*yi +C4) .
In this way, a set of equations can be constructed, which only depends on the unknown reflection coefficient and the unknown line parameters K in dependence of the measurement values Vl,i and Vr,i.
The line parameter and the reflection coefficient are thus calculable. This solution is based on the representation of the obstacle networks show no transmission.
The LRR calibration with an unknown obstacle on a planar microwave substrate is shown below.

This algorithm is based on the representation of the obstacle networks with pseudo transmission matrices. As the obstacles might also be realized as pure reflections, the networks cannot be described with transmission matrices, because in this representation a factor mi might become zero. The measurement matrix,

Where the primes indicate from which side of the setup the generator signal is fed. By multiplying the measurement matrices with the factor mi, the pseudo transmission matrices [Qi] result

The transmission characteristics in forward and reverse direction are described by µf,i and These values are related to the scattering parameters of the obstacle as follows:
In order to determine the unknown obstacle and line parameters, the obstacle networks are positioned as depicted in FIG: 9 & FIG: 11 respectively. Considering the setup shown below various pseudo transmission matrices can be constructed with measurement matrices.

On the basis of this representation certain trace relations can be evaluated and then can be transformed into a set of nonlinear equations and the unknown parameters can be determined. An approximate knowledge of the circuitsâ„¢ dimensions is necessary in order to choose the correct solutions.

Prior to 1965 nearly all microwave equipment utilized coaxial, waveguide, or parallel strip-line circuits. In recent years microstrip lines have been used extensively because they provide one free and accessible surface on which solid state devices can be placed. It is an unsymmetrical stripline, that is a parallel plate transmission line having dielectric substrate, one face of which is metalised ground and the other(top) face has a thin conducting strip of certain width Ëœwâ„¢ and thickness Ëœtâ„¢. Sometimes a coverplate is used for shielding purposes but it is kept much farther away than the ground plane so as not to affect the microstrip field lines. It is also called an open strip line. Modes on microstrip are only quasi transverse electromagnetic (TEM). Thus the theory of Tem- coupled lines applies only approximately.
Microstrip transmission lines consisting of a conductive ribbon attached to a dielectric sheet with conductive backing are widely used in microwave technology. Because such lines are easily fabricated by printed-circuit manufacturing techniques, they have a technical merit. Most microstrip lines are made from boards of copper with a thickness of 1.4 or 2.8 mils. Line width of less than 0.1 is uncommon.
There are various types of microstrip lines,
*Embedded microstrip lines.
*Standard inverted microstrip lines.
*Suspended microstrip lines.
*Slotted transmission lines.

Cost effective.
Provides uniform signal paths.
Better interconnection features and easier fabrication.
Numerical analysis of microstrip lines requires large digital computers
For long transmission lengths, they suffer from excessive attenuation per unit length.
They have higher radiation losses or interference due to the openness of the microstrip structure.

The complexity of the test fixture can be reduced.
The connectors of the VNA do not have to be placed at different distances from each other during calibration.
Enlargement of the bandwidth.
Improved accuracy.
The calibration structures can be realized very easily in microstrip technology.
Difficult to obtain an unknown obstacle whose electrical properties must not change when it is moved.
The frequency coverage of the line standard is approximately 8:1, so more line standards are needed to cover a wide frequency range.
An approximate knowledge of the circuitsâ„¢ dimensions is necessary in order to choose the correct solutions.
In free space systems where the variation of the antenna positions might be critical due to changes of the beam propagation.
When test fixture needs to be simple.
When the connectors of the analyzers measurement ports cannot be displaced.

Measurements of a planar stripline bandpass filter were performed with a VNA on the basis of the LRR method in comparison to the TRL method.
The measured scattering parameters show good agreement between the two methods.
The measurement results are shown next. The plots for both the magnitude and phase of S-parameters are given.

FIG: 14 TRL (- -) and LRR method (___ ) applied to a bandpass- filter
LRR technique is a new self-calibration procedure. The calibration circuits are all of equal mechanical length. This is advantageous for the calibration of vector network analyzers, such as, for instance, for applications where the connectors of the analyzers measurement ports cannot be displaced.
The robust functionality is confirmed by measurements, and for that the calibration circuits can be realized in microstrip technology. In the LRR method two solutions are there and depending on the realized calibration structures, the appropriate way should be chosen in order to improve the accuracy.
[1] Ilona Rolfes and Burkhard Schiek, LRR-A Self-Calibration Technique for the Calibration of Vector Network Analyzers, IEEE Transactions on instrumentation and measurement, vol 52, No. 2, pp.316-319, April 2003.
[2] H.Heuermann and B.Schiek, LNN-An alternative in-fixture calibration procedure, IEEE Transactions on Microwave Theory and Techniques, vol.45,pp. 408-413, Mar.1997.
[3] G.F.Engen and C.A.Hoer, Thru-reflect-line: An improved technique for calibrating the dual six port automatic network analyzer, IEEE Transactions on Microwave Theory and Techniques., vol. 27,pp. 987-993,Dec 1979.
[4] H.J.Eul and B.Schiek, A generalized theory and new calibration procedures for network analyzer self-calibration. IEEE transactions on Microwave Theory and Techniques., vol.39,pp.724-731, April 1991.
[5] Cletus A.Hoer, performance of a dual six-port automatic network analyzer, IEEE Transactions Microwave Theory and Techniques,vol-27, No.12,Dec 1979.
[7] Samuel.Y.Liao, Microwave devices and circuits, PHI.
[8] Kulkarni, Microwave and Radar Engineering.
4. MERITS 17

Post: #2
please read and for getting more information about Line-Reflect-Reflect Technique
Post: #3
i want a good ppt and pdf on "line reflect -reflect"
due to a semina purpose..Big Grin
Post: #4
i want sm standard PPTs on LRR techinque.
Post: #5
to get information about the topic line-reflect-reflect technique full report ,ppt and related topic refer the link bellow

Important Note..!

If you are not satisfied with above reply ,..Please


So that we will collect data for you and will made reply to the request....OR try below "QUICK REPLY" box to add a reply to this page
Popular Searches: unknown namespace vm, line reflect reflect technique ppt download, line reflect reflect technique slideshare, line reflect line calibration, calibration of mq 5, who is samuel gompers, application of line reflect reflect technique,

Quick Reply
Type your reply to this message here.

Image Verification
Image Verification
(case insensitive)
Please enter the text within the image on the left in to the text box below. This process is used to prevent automated posts.

Possibly Related Threads...
Thread: Author Replies: Views: Last Post
  A DSP based on on-line UPS seminar class 4 2,327 19-12-2015 01:10 PM
Last Post: seminar report asees
  How to Choose the Suitable Sand Washer in Sand Production Line? wanerjob 3 561 20-10-2014 08:37 PM
Last Post: wanerjob
  BROADBAND OVER POWER LINE (BPL) seminar projects crazy 38 23,246 30-08-2014 01:10 AM
Last Post: Guest
  Fractal Antennas: A Novel Miniaturization Technique for Wireless Communications seminar presentation 3 2,979 20-11-2012 01:17 PM
Last Post: seminar details
  MPEG-2 VIDEO COMPRESSION TECHNIQUE full report project topics 4 4,975 24-10-2012 12:21 PM
Last Post: Govind Mohan
Star INTER LINE UNIFIED POWER QUALITY CONDITIONER projectsofme 4 2,622 11-10-2012 03:05 PM
Last Post: seminar details
  Image Steganography Technique Based on Wavelet Transform science projects buddy 2 2,183 06-10-2012 01:25 PM
Last Post: seminar details
  Seminar Report On Line-Reflect-Reflect Technique mechanical wiki 3 3,044 13-02-2012 11:23 AM
Last Post: seminar paper
Last Post: seminar class
  Asymmetric digital subscriber line Computer Science Clay 1 1,055 23-03-2011 09:34 AM
Last Post: seminar class